Factory direct planting, piling, drilling, straight blade, digging machine blade, ice drilling blade
Our blade material includes:
٭ Carbon steel
٭ Rust resistant steel and stainless steel
٭ Tool steel
٭ Thickness between 0.06 -- 3.0 mm and top hardness between 40 -- 68 HRc
Our product range includes serrated, toothed, corrugated, curved, pointed, recessed, multi-edged and crank
special blades or blades in a variety of shapes and geometric combinations. Welcome new and old customers
to consult: Tony +86 1316595046 (WhatsApp/WeChat)
Our blades have many advantages
♦ Rich experience in blade production
♦ Quality is stable and reliable
♦ Recommend suitable materials for use purposes
♦ Provide project consulting and development
♦ Maximum flexibility in development
♦ The first sample knives will be ready in a matter of days for near-mass production
♦ During the use of blade cutting sharp, durable blade replacement times less, high production efficiency
♦ Stable quality reduce labor, reduce costs and improve efficiency ♦ Factory direct sales, low scrap rate
You can check the blade you need from our website, different materials, different specifications and sizes of
different prices, when you have special needs, welcome to inquire: +86 13016595046 Tony (WhatsApp/WeChat)
The major weapons of ice fishing are ice harvesting tools, including ice md and ice drill, but also those with
pickaxes, such as those seen at Angezhuang Reservoir, such as Those li Kui used. Fish rate is proportional to
the number of ice holes, good weapons can improve the fish rate.
Ice drill is divided into non-power ice drill (hand ice drill), power ice drill (electric ice drill, gasoline ice drill) two
categories. The more well-known ice drill west ice drill and so on.
"Good drill does not need to add power", a good hand ice drill, just need to keep horizontal vertical shaking.
There is no need to press down, the drill will go down by itself, the ice is evenly cut, and there will be no ice jam
and other phenomena when drilling through the bottom of the ice. Many anglers feel unable to drill through the
ice and think their strength is small, so they add motor and gasoline engine, which not only increases the cost, but
also increases the baggage. Practice has proved that as long as the drill is good, without adding power such as
electric oil, it can meet the needs of drilling ice holes in one day (in the winter of 2009, when the ice is 45 cm thick,
a good hand ice drill actually drilled to 50 eyes a day). On the contrary, if the drill is not good, the resistance is too
large, and the hand is laborious, even if the power is added, it will easily consume electricity and oil. (The resistance
of the bit comes from the diameter of the bit, the edge of the bit blade, the horizontal and vertical Angle of the bit
blade, whether the blade is strictly symmetrical on the same cone surface, etc.)
Blade: ice drill should be easy to use, the blade is the key, the sharpness of the blade and the blade to eat ice Angle
determines whether the ice drilling is comfortable and labor-saving.
The Angle formed by ice drill blade and ice is very important -- eating ice too steep requires great strength to shake
the ice drill, suitable for people with great strength type anglers, weak shaking. The Angle of the blade to the ice is too
slow, which makes it easy to slip and requires downward force to drill through the ice when shaking horizontally. The
most ideal state is that the ice drill can evenly eat the ice down, there is no need to press the ice drill down hard, shaking
up the force is moderate, the common blade Angle is about 30-40 degrees.
Ice drill blade generally has two, there are one and four, blade shape is divided into straight and circular half moon shape,
shaped, etc., the circular blade forms a cone, drilling into the ice, the drill is not easy to slide without positioning.
Drill pipe and crank: the combination of drill pipe and crank can be fixed by concentric steel pipe screws (which are easy
to loosen) or can be folded and opened. Both methods require drill pipe and crank strictly vertical concentric, the connection
part should be less, otherwise it is easy to loose the frame swing, non-concentric crank (left and right hand holding position
is not the same vertical line with the drill bit) can be used with both hands, ice drilling speed is faster than the single-arm
force of the hand crank.
Tip diameter: Determines the size of the ice hole. Domestic anglers generally prefer 6-7 inches (15-18 cm) in diameter. The
larger the diameter, the greater the resistance. Big anglers in Europe and America usually use 7-8 inch hand drills. Power ice drill
can use 7-8 inches (still need to consider the current, torque and other parameters matching, or soon run out of electricity),
electric ice drill is best with 6, 7 inch drill, gasoline power can be with 7, 8 inch drill, or even bigger, big ice hole on the big fish
do not need to expand the ice hole, the ice hole is not easy to freeze.
Welcome new and old customers to consult, tel: +86 13016595046 Tony (WhatsApp/WeChat)
Reasons for choosing us:
As a professional blade manufacturer for 18 years, we have rich experience in the treatment and selection of coating for
blades of different shapes. We provide you with ideal cutting solutions and suggestions, accurate material selection and
strict skilled production process. We are committed to providing you with sharper, longer life of high quality cutting blades
to provide your production cutting efficiency. Fast sample, easy to cut, no burr, stable quality.